Pre-wall installation systems, Mounting frames: C101

Water connection from the back or top via mounting holes	G1/2 "
Functional range of water pressure	0,05 – 1,6 MPa
Recommended range of water pressure	0,3 – 0,5 MPa
Big flush	6 – 9 l
Small flush	2,5 – 3,5 l
Factory setting of large flush	6 l
Factory setting of small flush	3 l
Hygienic reserve	3 l
Water volume in the cistern	9 l
Load test	400 kg

For wall-hung WC
For mounting in front of a support wall or in to a plasterboard construction
For floor thickness 0–200 mm
For installation of wall-hung WC pans with a connecting pitch of 180 mm or 230 mm

Sliding rail holder for the waste connector can be set to eight positions between 0–93 mm
Angle valve with the ability to connect to the Mepla piping system
The frame allows the anchoring to a separate sufficiently strong plasterboard partition, in front of the bearing wall
The installed module is covered with a plasterboard panel and there is no need for any additional fixing or anchoring elements
The construction of polystyrene insulation prevents condensation forming on the surface of the tank and dampens the vibrations from the tank into the building structure
Prepared for connecting a bracket with a DG 1/2” conversion for bidet seats and sprays
Dual flush independently adjustable with hygienic reserve
Suitable for installation of remote or sensor flushing
Compatible with all Alca and Komfort flush plates
Maintenance work without using any tools
Water supply from the rear/top
The cistern is made of one piece, thus ensuring 100% impermeability
The service opening cover simplifies assembly and prevents the penetration of moisture and impurities
Installation depth adjustable from 20–95 mm
Installation depth 125 mm
Frame material: powder-coated metal

Cistern with fill and flush valve
Self-supporting frame
Fittings 1/2" water connection with the integrated angle valve Schell 1/2–3/8"
Fixation set: screw Ø8×60 – 4 pcs, dowel Ø12 – 4 pcs
Fixation material for fixing the WC pan: threaded rod M12 – 2 pcs, washers – 4 pcs , cover – 2 pcs, nut – 2 pcs, thread protector – 2 pcs
Elbow waste connector HT 90/90 polyethylene, PE-HD
Waste reduction HT 90/110 polyethylene, PE-HD
Inlet seal, PP outlet, wrapping seal
Drainage seal, PP connector, connector seal
End-caps set for protecting the connecting holes during installation of the system
The 2 piece cover of the service opening is simply adjustable
Flush plate C170

M0005-ND	Water supply ring A100
M0017-ND	Inlet fill valve bracket
M0021-ND	Inlet sealing (WC systems)
M0023-ND	Wrapping seal 45×58×25 (WC systems)
M0026-ND	Waste sealing (WC systems)
M0028-ND	Coupler sealing
M0029-ND	Waste pipe holder
M0042-ND	Flush plate frame spring
M0043B-ND	Inner board
M0080-ND	Sleeve lid
M0243-ND	Nut for angle valve bracket
M903-ND	Threaded rods + accessories
M905-ND	Complete mechanism
M916-ND	Fixation set
MN0091-ND	Frame sleeve
MN0092-ND	Frame for WC system sleeve
MN0101-ND	Flush plate frame
MN0114-ND	Flush plate frame pods 4 pcs
MN0115-ND	Pipe with O-ring for WC systems
MN0118-ND	Flush plate screw spring
MN0121C-ND	Stopper
P146-ND	Template for setup of flush plates

C101